SYLLABUS OF KUK ELECTRICAL AND ELECTRONNICS ENGG BTECH 6TH

MICROPROCESSOR & APPLICATIONS
VI SEM. EEcT-302-E
Theory –100 Marks
L T P Total Sessional-50 Marks
4 1 - 5 Duration: 3Hrs
UNIT I
Introduction to microprocessor, its advantage & limitations: Various type of processors including the special purpose; the concept of stored programme architecture; machine & instruction cycle timing; single chip vs. chip set microprocessor.
UNIT II
Microprocessor architecture& programming - Detailed description of 8085 pins, flags, registers etc.; generation of system clocks power on reset; addressing mode; instruction set; stack operation; sub routine & macros; interrupts; assembler directive languages programming
Buses: Parallel Vs serial; bus buffering tri stating noise; loading & reflection problem – an introduction only; bus standards like RS422/432, IEEE438, RS232.
UNIT III
Interfacing: Memory mapped I/O & input/output mapped I/O space, various data transfer techniques programme data transfer techniques, interrupt data transfer techniques, DMA.
Memory: Interfacing of the memory, various kinds of Memory (RAM, ROM, EPROM, EEPROM), IC 8755.
UNIT IV
Special purpose support devices & Application: Brief description & interfacing of 8255 PPI & 8253, 8251 USART & A/D ,D/A Chips , applications- A temperature monitoring system & closed loop control. Introduction to micro controller & advanced 8086 microprocessor & its architecture, comparison of 8086 & 8085.
NOTE: The question paper shall have eight questions in all organized into four sections, each section having two questions from each of the four units. The candidate shall have to attempt five questions in all , selecting at least one question from each unit.
References:
1.
R.S. GAONKAR: Microprocessor architecture, programming & Application.(MGH)
2.
Malvino, A.P. : Digital computer electronics-an Introduction to microprocessor.(MGH)
3.
D.V.HALL: Microprocessor & Digital circuits.(MGH)
4.
MATHUR A.P. : Introduction to microprocessor


POWER SYSTEM ANALYSIS & PROTECTION
VI SEM. EEcT- 304-E
L T P/D Total Theory : 100 Marks
3 1 - 4 Sessional: 50 Marks
Duration : 3Hrs
UNIT I
Characteristics & representation of components of a power system, synchronous machines, transformers, lines cables & loads. Single line diagram.
Protective Relaying : Scheme of protection of generators, transformers, transmission lines & bus-bars, carrier current protection.
UNIT II
Circuit Interruption : Circuit interruption, theory of arc formation and it’s excitation in d.c., a.c. circuits, restriking & recovery voltage, interruption of capacitive & inductive currents. Rupturing capacity & rating of circuit breakers.
Circuit-Breakers : Classification of circuit-breakers, circuit-breakers of low medium, high & extra high voltages. Multibreak & resistance switching. Autorestoring of high capacity & H.V. circuit breakers.
UNIT III
Fault Analysis:- Symmetrical faults: calculation of fault currents, use of current limiting reactors.
Unsymmetrical faults: Types of transformation in power system analysis, symmetrical components transformation, sequence impedance of power system elements, Sequence network of power system analysis of unsymmetrical short faults sequence components filters, Network analysis & it’s application to interconnected system.
UNIT IV
Transients in Power Systems: Transient electric phenomenon, lighting & switching surges, travelling waves, reflection & refraction of waves with different line termination, Protection against dangerous pressure rises.
Stability of power System: Concepts of stability, power angle characteristics of Synchronous, steady state & transient stability swing waves.
NOTE: The question paper shall have eight questions in all organized into four sections, each section having two questions from each of the four units. The candidate shall have to attempt five questions in all, selecting at least one question from each unit.
References:
1.
Elements of power system analysis by W.D. Stevenson.
2.
Electric Power System by B.M. Weddy.
3.
The transmission & Distribution of electric energy by H.Cotton.
4.
Modern Power System Analysis by I.J. Nagrath & D.P. Kothari.
5.
A course in Electrical Power by Soni, Gupta & Bhatnagar.
6.
Power System Analysis & Stability by S.S. Vadhera
7.
Electrical Power System by C.L. Wadhwa. 8. Electrical Power System by Ashfag Hussain.
9. Electrical Power by S.L. Uppal.
10. Switching & Protection by Sunil S. Rao.


DESIGN OF ELECTRICAL MACHINES
VI SEM. EEcT-306-E
L T P/D Total Theory : 100 Marks
3 1 - 4 Sessional : 50 Marks
Duration : 3 Hrs.
UNIT I
DC MACHINES :Output equation, choice of specific loadings, choice of poles and speed, Design of conductors, windings, slots field poles, field coils, commutator and machine design.
UNIT II
SYNCHRONOUS MACHINES: Specifications, ratings and dimensions, specific loadings, main dimensions, low speed machines, turbo generators, armature conductors, cooling.
UNIT III
INDUCTION MOTORS: Three Phase Induction Motor: Standard specifications, output equations, specific loadings, main dimensions, conductor size and turns, no. of slots, slot design, stator core, rotor design, performance calculations.
Single Phase Induction Motor: output equations, specific loadings, main dimensions, design of main and auxiliary winding, capacitor design, equivalent circuit parameters, torque, efficiency,
UNIT IV
TRANSFORMERS: Standard specifications, output equations, design of core, coil, tank and Cooling tubes, calculation of circuit parameters, magnetizing current, losses and efficiency, Temperature rise and regulations from design data.
NOTE: The question paper shall have eight questions in all organized into four sections, each section having two questions from each of the four units. The candidate shall have to attempt five questions in all , selecting at least one question from each unit.
TEXT BOOKS
1.
M.G.Say, Performance and design of ac machines, CBS Publishers and distributors, New Delhi, 1983.
2.
S.K. Sen., Principles of electrical machine design with computer programs, Oxford and IBH publishing co. 1987.
REFERENCES
1.
J.H. Kuhlmann, Design of electrical operators, John Willey, 1957.
2.
CG Veinott, Theory and design of small induction machines, MGH, 1959.
3.
A Shanmugasundarem, Electrical machine design databook, John willey, 1979.


DIGITAL SIGNAL PROCESSING
VI SEM. EEcT-308-E
L T P/D Total Theory : 100 Marks
4 1 - 5 Sessional: 50 Marks
Duration : 3Hrs
UNIT I
The Z – Transform Analysis of LTI System:- Transform its properties, System Function of a linear Time- Invariant system. Inversion of the Z-Transform, the one-sided Z-transform, Solution of difference equations. Analysis of LTI system in Z- domain, transient and steady- state response. Causality and stability. Pole- Zero Cancellations. Shur- Cohn Stability test. Jury Test Shur-Cohn-fuzzivera stability criterion.
UNIT II
DFT and FFT: DFT and its properties, Circular Convolution and fast linear convolution, Linear filtering using DFT. Direct Computation of DFT, FFT algorithms, Radix-2 and Radix-4 algorithms. Goetzel Algorithm, Chirp-Z Transform algorithm.
UNIT III
Implementation of Discrete-Time Systems: Structure for FIR Systems-direct form, Cascade form, Frequency-Sampling and Lattice structures, Structures for IIR-direct form, signal flow graphs and transpose structures. Cascades form and lattice structures, state space structure.
Design for Digital Filters:- Design for FIR filters-using window method ( hamming window,
rectangular window), using frequency of IIR filters from Analog filters by approximation of derivatives, by impulse invariance by Transformation, Matched Z-Transformation Characteristics of commonly used analog filters.
UNIT IV
Time Frequency Analysis: Introduction to wavelets and wavelet transforms.
Brief Introduction to DSP Architecture: Pipeline, Lattice and systolic architecture.
NOTE: The question paper shall have eight questions in all organized into four sections, each section having two questions from each of the four units. The candidate shall have to attempt five questions in all , selecting at least one question from each unit.
References:
1.
Digital Signal Processing by J.G. Proakis and D.G. Manalakis-PHI
2.
Digital Signal Processing by: A.V. Oppenheim and R.W. Schafer-PHI
3.
Element of Digital Signal Processing by N. Sarkar Khanna Publishers.
4.
Digital Signal Processing by S. K. Mitra –TMH.
5.
Digital Signal Processing by Rabinar, Gold-PHI
6.
Digital Signal Processing by S. Salivahanan- TMH
7.
Digital Signal Processing by IFecher


ELECTRIC DRIVES AND CONTROL
VI SEM. EEcT-310-E
L T P/D Total Theory : 100 Marks
3 1 - 4 Sessional : 50 Marks
Duration : 3Hrs
UNIT I
Introduction:- Definition & classification of different type of drives, Review of characteristics and components of electric drives, Speed control methods of various a.c. and d.c. drives, its advantages and applications, acceleration and retardation time, energy consideration.
Braking of drives:- Various methods of braking of a.c. and d.c drives, Automatic control arrangement, characteristics and application, acceleration and Retardation time ,Energy consideration.
Induction motor (A.C) drives:- Basic principle of induction motor drives, 3 ∅ a.c voltage controller fed I.M drive, variable frequency control, voltage source inverter (VSI) and current source inverter (CSI), cycloconverter fed IM drive, Slip Power control, static rotor resistance control, chopper control of 3 -∅ slip ring induction motor.
UNIT II
D.C. drives:- Rectifier controlled circuits, Single phase fully controlled and half controlled rectifier fed separately excited d.c motor, 3∅ fully and half controlled fed separately excited d.c. Motor, performance and characteristics of single phase and 3∅ rectifier controlled d.c drives. Control techniques of d.c. Drives using chopper, multi quadrant control of chopper fed motors.
UNIT III
Dynamics of Electric drives:- Fundamental load torque equation, permissible frequency of starting and stopping, definite time, speed and current limit control, Automatic starting and pulling operation of synchronous motors.
Digitally Controlled (Microprocessor control of Electric drives) :- Application areas and functions of HP in drive technology, Block diagram of arrangement and comparison with other method, components for digital control, vector control of IM drive using HP.
UNIT IV
Traction Drives:- Nature of traction load, motors, conventional d.c & a.c traction drives, charactertics, d.c traction using chopper controlled d.c motors, polyphase a.c motors for traction drives, speed time relationship.
Rating of motors:- Determination of motor rating, Nature of loads and classes of motor duty, frequency of operation of motor subjected to intermittent loads, pulse loads etc.
NOTE: The question paper shall have eight questions in all organized into four sections, each section having two questions from each of the four units. The candidate shall have to attempt five questions in all, selecting at least one question from each unit.
References:
1.
Electric drives by S.K.Pillai, Wiley.
2.
Thyrister D.C Drives by S.K.Sen.
.
Control System in Industry by Siskind, McGraw Hill. 4. Electric Machines & Drives by Fransver. Relevant I.S.I. Cader.


ELECTRICAL MATERIALS AND PROCESSES
EEcT-312-E
L T P/D TOTAL Theory : 100 Marks
3 1 - 4 Sessional : 50 Marks
Duration : 3 Hrs
UNIT 1
Conductors,Properties of conductors ,ACSR, High resistivity materials and their properties, Alloys, Soldering and brazing materials, superconductivity, super conductor materials and their applications.
UNIT 2
Insulators,classification of insulators, dielectric materials, glass and ceramics, refractory materials and their uses, optical fibers, lasers and opto-electronics materials, semiconductor materials, properties of semiconductor materials thermosetting and thermoplast materials.
UNIT 3
Classification of material, dia , para, and ferro magnetic materials-curie law and curie weiss law (qualitative study).Ferromagnetism-Qualitative study of domain theory-Hysterisis phenomena. Hard and soft magnetic material and their applications. Ferrites, Structure and property.
UNIT 4
Processes used in Plano technology e.g. lapping, polishing, cleaning, masking, photolithography, diffusion, oxidation and Metallization, welding wire bonding, packaging and encapsulation, Heating- induction and dielectric, Electron beam welding and cutting, annealing,cold & Hot rolling
NOTE: The question paper shall have eight questions in all organized into four sections, each section having two questions from each of the four units. The candidate shall have to attempt five questions in all , selecting at least one question from each unit.
REFERENCE :
1. Kasap S.O. Principles of Electrical Engg. Material and Devices(MGH)
2. Mahajan Principles of growth and processing of semiconductors(MGH)
3 Dhir. Electronics components and materials and principles
Manufacturing & Maintenance (TMH)
4. Addision: Electronics Engg. Material Devices (TMH)
5. Ruska N scot: Microelectronics processing an introduction to the manufacturer
of integrated Circuits(MGH)
6. Seth & Gupta: A course in electrical Egg. Materials(Dhanpat Rai & Sons)
7. Dekker: Electrical Engg. Materials(PHI)



THIS SERVICE IS PRODUCED BY UNIQUE GROUP.www.uniqueinstitutes.org ,for fun www.flowerrose81.blogspot.com, FOR FREE ADVERTISEMENT www.pathakadvertisement.blogspot.com

»»  read more

Read more...

SYLLABUS OF KUK CIVIL ENGG BTECH

INTRODUCTION TO BIOTECHNOLOGY
(BT-101 E)
L T P/D Theory: 100 marks
3 1 Sessional : 50 marks
Total: 150 marks
Time: 3 Hrs.
UNIT - I
Introduction to life: Characteristics of living organisms. Hierarchy of organisation and factors responsible for regulating different levels of organisations. Structure of Prokaryotic and Kukaryotic cell. Basic concept of State and Homeostasis.
Introduction to Biomolecules: Definition, general classification and important functions of carbohydrates, lipids, proteins, nucleic acids and vitamins.
Enzymes as biocatalysts: General characteristics, nomenclature and classification of Enzymes. Effect of temperature, pH, enzyme and substrate concentrations on the activity of enzymes. Elementary concept of cofactors and coenzymes.
UNIT - II
Biodiversity :
(i) Plant System : Basic concepts of plant growth, nutrition, photosynthesis and nitrogen fixation. Types of Growth regulators and their physiological effects.
(ii)
Animal System : Elementary Study of Digestive, Respiratory, Circulatory, Excretory systems and their functions.
(iii)
Microbial System : History of Microbiology, types of microbes and properties. Economic importance and control of microbes.
UNIT - III
Evolution: Theories of evolution. Mendel’s laws of inheritance. Variation and speciation.
Genetic: Cell division – Mitosis and Meiosis. Evidence of nucleic acids as a genetic material. Central Dogma.
Genetic Engineering : Elementary knowledge of Recombinant DNA Technology, Bio-informatics and Genomics.
UNIT – IV
Introduction to Biotechnology : Definition, scope and achievements. Tools used in biotechnology.
Applications of Biotechnology in Agriculture, Medicine and Environment – an elementary knowledge.
Prospects and public perception of Biotechnology.
Text/ Reference Books:
1.
Cell Biology and Genetics. 9th edition. Starr, C. and Taggard; R. (2001) Thomson Learning USA.
2.
Life Science of Biology 6th edition Purves W.K.; Sadava, D.; Orians, G.H. and Heller, H.C. (2001). W.H. Freeman & company, USA.
3.
Basic Biotechnology. Ratledge, C. and Kristiansen, B. (2001) Cambridge University Press.
4.
Basic Biotechnology. Ignacimuthu, S.J. (2002) Tata McGraw-Hill Pub., New Delhi
5.
Genes VII Lewis Benjamin (2002). Oxford Univ. Press Oxford.
6.
Biotechnology 3rd Edition. Smith, J.E. (2003) Cambridge University Press.
ME-101E
ELEMENTS OF MECHANICAL ENGINEERING
L T P Theory: 75 marks
3 1 Sessional: 25 marks
Total: 100 marks
Time: 3 Hrs.
Unit-I
Properties of Steam & Boilers: Formation of steam at constant pressure, Thermodynamics properties of steam, Condition of steam, Steam tables, Measurement of dryness fraction by throttling calorimeter, Classification of boilers, Comparison of water and fire tube boilers mounting and accessories with their functions, Constructional and operational details of Cochran and Babcock and Wilcox boilers, Problems.
Steam Turbines and Condensers: Classification of turbines, Working principle of impulse and reaction turbine, Compounding of impulse turbine, Comparison of impulse and reaction turbines, Types of condensers, Cooling ponds and cooling towers, Condenser and vacuum efficiencies.
Unit-II
I.C. Engines and Gas Turbines: Introduction, Classification, Constructional details and working of two-stroke and four-stroke diesel and petrol engines, Otto, Diesel and Dual cycles, Working principle of gas turbine, Constant pressure gas turbine cycle.
Water Turbines, Pumps and Hydraulic Devices: Introduction, Classification, Construction details and working of Pelton, Francis and Kaplan turbines, Specific speed and selection of turbines, Classification of water pumps and their working, Hydraulic jack and lift.
Unit-III
Simple Lifting Machines: Definition of machine, Velocity ratio, Mechanical advantage, Efficiency, Laws of machines, Reversibility of machine, Wheel and axle, Differential pulley block, Single, double and triple start worm and worm wheel, Single and double purchase winch crabs, Simple and compound screw jacks. Problems.
Power Transmission Methods and Devices: Introduction to Power transmission, Belt drive, Rope drive, Chain drive, Pulley, Gear drive, Types of gears, Gear train, Clutches, Types and function of clutches, Types and function of brakes, Power measurement by dynamometer, Types of dynamometers.
Unit-IV
Stresses and Strains: Introduction, Concept & types of Stresses and strains, Poison’s ratio, stresses and strains in simple and compound bars under axial loading, Stress-strain diagrams, Hooks law, Elastic constants & their relationships, Principle stresses & strains and principal- planes, Mohr’s circle of stresses. Numerical problems.
Bending Moment & Shear Force: Definitions, SF and BM diagrams for cantilever and simply supported beam. Calculation of maximum SF, BM and point of contra-flexure under the loads of (i) concentrated load (ii) uniformly distributed load (iii) combination of concentrated and uniformly distributed loads. Problems.
Text Books:
1. Strength of Materials - G.H. Ryder, Pub.- ELBS.
2. Hydraulic and Fluid Mechanics – Modi and Seth, Pub. – Standard Book House, New Delhi
3. Engineering Thermodynamics – C.P. Arora, Pub. - TMH, New Delhi
4. Thermal Engineering – A.S. Sarad, Pub. - Satya Prakashan, New Delhi.
5. Engineering Mechanics – K.L. Kumar, Pub. - TMH, New Delhi.
6. Theory of Machines – S.S. Rattan, Pub. – TMH, New Delhi.
Reference Books:
1.Strength of Materials – Popov, Pub. - PHI, New Delhi.
2. Hydraulic Machines – Jagdish Lal, Pub.- Metropolitan, Allahbad.
3. Thermal Science and Engineering – D.S. Kumar, Pub. – Kateria & Sons, New Delhi.
ME- 103E
MANUFACTURING PROCESSES
L T P Theory : 100 marks
4 Sessional : 50 marks
Total: 150 marks
Time: 3 Hrs.
Unit-I
Introduction: Introduction to Manufacturing Processes and their Classification. Industrial Safety; Introduction, Types of Accidents, Causes and Common Sources of Accidents, Methods of Safety, First Aid.
Engineering Materials: General Properties and Applications of Engineering Materials, Mild Steel, Medium Carbon Steel, High Carbon Steel, High Speed Steel and Cast Iron.
Unit-II
Foundry: Introduction to Casting Processes, Basic Steps in Casting Process, Pattern, Types of Patterns, Pattern Allowances, Risers, Runners, Gates, Moulding Sand and its composition, Sand Preparation, Molding Methods, Core Sands and Core Making, Core Assembly, Mold Assembly, Melting ( Cupola) and Pouring, Fettling, Casting Defects and Remedies.
Unit-III
Cold Working ( Sheet Metal Work ): Sheet Metal Operations, Measuring, Layout Marking, Shearing, Punching, Blanking, Piercing, Forming, Bending and Joining Advantages and Limitations.
Hot Working Processes: Introduction to Hot Working, Principles of Hot Working Processes, Forging, Rolling, Extrusion, Wire Drawing. Plant Layout, Objectives of Layout, Types of Plant Layout and their Advantages.
Unit-IV
Introduction to Machine Tools: Specifications and Uses of commonly used Machine Tools in a Workshop such as Lathe, Shaper, Planer, Milling, Drilling, Slotter, Introduction to Metal Cutting. Nomenclature of a Single Points Cutting Tool and Tool Wear. Mechanics of Chips Formations, Type of Chips , Use of Coolants in machining.
Welding: Introduction to Welding, Classification of Welding Processes, Gas Welding: Oxy-Acetylene Welding, Resistance Welding; Spot and Seam Welding, Arc Welding: Metal Arc, TIG & MIG Welding, Welding Defects and Remedies, Soldering & Brazing.
Text Books :
1.
Workshop Technology Vol. I &II - Hazra & Chaudhary, Asian Book Comp., New Delhi.
2.
Process and Materials of Manufacture-Lindberg, R.A. Prentice Hall of India, New Delhi.
3.
Principles of Manufacturing Materials and Processes- Campbell, J.S.- McGraw- Hill.
Reference Books:
1.
Manufacturing Science-Amitabha Ghosh & Ashok Kumar Malik, - East-West Press.
2.
Manufacturing Process and Systems - Ostwald, Munoz , John Wiley.
3.
Workshop Technology, Vol. 1, 2 & 3 – Chapman, WAJ, Edward Arnold.
.
CSE -101E
FUNDAMENTALS OF COMPUTERS & PROGRAMMING IN C
L T P Theory: 100 marks
3 2 Sessional: 50 marks
Total: 150 marks
Time: 3 Hrs.
Unit-1
An Overview of Computer System: Anatomy of a digital Computer, Memory Units, Main and Auxiliary Storage Devices, Input Devices, Output Devices, Classification of Computers. Radix number system: Decimal, Binary, Octal, Hexadecimal numbers and their inter-conversions; Representation of information inside the computers. Operating System Basics: Introduction to PC operating Systems: DOS, Unix/Linux, Windows 2000.
Unit-2
Programming Languages: Machine-, Assembly-, High Level- Language, introduction to Assembler, Compiler, Interpreter, Debuggers, Linker and Loader. Programming fundamentals: problem definition, algorithms, flow charts and their symbols.
Internet basics: How Internet works, Major features of internet, Emails, FTP, Using the internet.
Unit-3
C Programming language: C fundamentals, formatted input/ output, expressions, selection statements, loops and their applications; Basic types, arrays, functions, including recursive functions, program organization: local and external variables and scope & arrays.
Unit-4
Strings: strings literals, string variables, I/O of strings, arrays of strings; applications. Structures, Unions and Enumerations: Structure variables and operations on structures; Structured types, nested array structures; unions; enumeration as integers, tags and types. Standard library: Input / output; streams, file operations, formatted I/O, character I/O, line I/O, block, string I/O, Library support for numbers and character data, error handling:
Text Books:
1.
Using Information Technology, 5th Edi, Brian K Williams & Stacey C. Sawyer, 2003, TMH
2.
The C Programming Language by Dennis M Ritchie, Brian W. Kernigham, 1988, PHI.
3.
C Programming – A modern approach by K.N. King, 1996, WW Norton & Co.
Reference Books:
1.
Information technology, Dennis P. Curtin, Kim Foley, Kunal Sen, Cathleen Morin, 1998, TMH
2.
Theory and problem of programming with C, Byron C Gottfried, TMH
3.
Teach yourself all about computers by Barry Press and Marcia Press, 2000, IDG Books India.
4.
Using Computers and Information by Jack B. Rochester, 1996, Que Education & Training.
.



THIS SERVICE IS PRODUCED BY UNIQUE GROUP.www.uniqueinstitutes.org ,for fun www.flowerrose81.blogspot.com, FOR FREE ADVERTISEMENT www.pathakadvertisement.blogspot.com

»»  read more

Read more...

INDIAN SCIENCE REASERCH ORGANISATION

Government of India

Department of Space

Vikram Sarabhai Space Centre (VSSC)

Thiruvananthapuram-695022, Kerala
Advertisement No. VSSC-253
VSSC invites application for the following posts :

1.Engineer (Civil) : 07 posts , Pay : Rs. 25000/- per month, Qualification : BE/B.Tech. or its equivalent in Civil Engineering with First Class with an aggregate of minimum of 65% marks.

2.Engineer (Electrical) : 06 posts, Pay : Rs. 25000/- per month, Qualification : BE/B.Tech. or its equivalent in Electrical Engineering with First Class with an aggregate of minimum of 65% marks.

Age : 35 years
How to Apply : Application in the prescribed format completed in all respects should reach the following address on or before 15/05/2010 by ordinary post in a cover superscribed “Application for the post of Engineer (Civi/Electrical)” (Advt. no. 253 dated 29/04/2010). Please visit http://www.vssc.gov.in/ for more information.



THIS SERVICE IS PRODUCED BY UNIQUE GROUP.www.uniqueinstitutes.org ,for fun www.flowerrose81.blogspot.com, FOR FREE ADVERTISEMENT www.pathakadvertisement.blogspot.com

»»  read more

Read more...